Bootrom start
Boot Media: eMMC
Decrypt auxiliary code ...OK
lsadc voltage min: 00000000, max: 00000004, aver: 00000001, index: 00000005
Enter boot auxiliary code
Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Jul 27 2018 - 00:49:01
Reg Version: v1.5.0\
Reg Time: 2020/03/28 12:05:14
Reg Name: hi3798mv3dms1_hi3798mv300_DDR3-1866_1GB_16bitx2_2layers.reg
dms board
Boot auxiliary code success
Bootrom success
System startup
Relocate Boot
Jump to C code
Fastboot 3.3.0-dirty (zhuhengxuan@ubuntu141-PowerEdge-R730) (May 14 2022 - 17:31:31)
Fastboot: Version 3.3.0
Build Date: May 14 2022, 17:31:48
CPU: Hi3798Mv300
Boot Media: eMMC
DDR Size: 1GB
Found flash memory controller hifmc100.
no found nand device.
MMC/SD controller initialization.
mmc cardtype 00000057
mmc cardtype fixed 00000017
scan edges:2 p2f:2 f2p:4
mix set temp-phase 7
scan elemnts: startp:35 endp:29
Tuning SampleClock. mix set phase:[07/07] ele:[05/09]
World CID MID :f4012242
World CMD 13, response = 900
World CMD 60, response = 900
World CMD 60, response = 900
World Read FW Ver, Start
World <FW> 52 38 32 2d 2c c9 53 43 31 38 51 32 39
World it is New emmc fw version S0318!!
World Test 1!!! ret 0
MMC/SD Card:
MID: 0xf4
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7376M Bytes (High Capacity)
Name: "Biwin "
Chip Type: MMC
Version: 5.0
Speed: 200000000Hz
Mode: HS200
Voltage: 1.8V
Bus Width: 8bit
Boot Addr: 0 Bytes
Net: up, down, gmac0
Boot Env on eMMC
Env Offset: 0x00400000
Env Size: 0x00010000
Env Range: 0x00010000
SDK Version: HiSTBAndroidV600R003C01SPC031_patch5
check remote recovery button begin
selinux_flag is androidboot.selinux=
bootargs:console=ttyAMA0,115200 blkdevparts=mmcblk0:4M(fastboot),4M(bootargs),12M(recovery),4M(deviceinfo),8M(baseparam),8M(pqparam),20M(logo),20M(logobak),35M(fastplay),35M(fastplaybak),10M(ystinfo),40M(kernel),20M(misc),40M(trustedcore),800M(backup),1000M(system),800M(cache),50M(private),8M(securestore),-(userdata)
==Enter recovery!
recoverybootargs:console=ttyAMA0,115200 blkdevparts=mmcblk0:4M(fastboot),4M(bootargs),12M(recovery),4M(deviceinfo),8M(baseparam),8M(pqparam),20M(logo),20M(logobak),35M(fastplay),35M(fastplaybak),10M(ystinfo),40M(kernel),20M(misc),40M(trustedcore),800M(backup),1000M(system),800M(cache),50M(private),8M(securestore),-(userdata)
Automatic boot of image at addr 0x01000000 ...
Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.18.24_hi3798mv2x
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3912193 Bytes = 3.7 MiB
Load Address: 02000000
Entry Point: 02000000
Loading Kernel Image from 0x16777280 to 0x33554432 ... OK
OK
ATAGS [0x00000100 - 0x000003E8], 744Bytes
Starting kernel ...
Uncompressing Linux...
XZ-compressed data is corrupt
-- System halted
Bootrom startFailed to send type frame. It may be caused by the following reasons:
- The board is not powered on or off again;
- The selected serial port is incorrect;
- The bootstrap function of the chip OTP is disabled.
Failed to download fastboot!
无论怎么折腾，最后都报这个错，是不是真成砖了~~
