我刷到hinas显屏了，但跑码到一半就停了
Bootrom start
Boot from eMMC
Initializing DDR ... OK
Starting DDR training ... OK
Starting fastboot ...
System startup
Reg Version: v1.1.0
Reg Time: 10/25/2014 8:34:16 Phi3798mdmo1d_hi3798mv100_ddr3_2gbyte_8bitx4_4layers_emmc.reg
Reg Name: hi3798mdmo1d_hi3798mv100_ddr3_2gbyte_8bitx4_4layers_emmc.reg
Compressed-boot v1.0.0
Uncompress.....................Ok
System startup
Reg Version: v1.1.0
Reg Time: 10/25/2014 8:34:16 Phi3798mdmo1d_hi3798mv100_ddr3_2gbyte_8bitx4_4layers_emmc.reg
Reg Name: hi3798mdmo1d_hi3798mv100_ddr3_2gbyte_8bitx4_4layers_emmc.reg
Fastboot 3.3.0-00361-gdaebe33-dirty (liuhh@HW-TV-S5) (Apr 29 2015 - 17:11:39)
Fastboot: Version 3.3.0
Build Date: Apr 29 2015, 17:12:08
CPU: Hi3798Mv100 (CA)
Boot Media: eMMC
DDR Size: 1GB
Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
MMC/SD controller initialization.
MMC/SD Card:
MID: 0x11
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 3776M Bytes (High Capacity)
Name: "004GE"
Chip Type: MMC
Version: 4.0
Speed: 25000000Hz
Bus Width: 8bit
Boot Addr: 0 Bytes
Boot Env on eMMC
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000
HI_OTP_LockIdWord,299: ID_WORD have already been locked
SDK Version: HiSTBAndroidV600R001C00SPC053_v2014101420
get key value 0x0
HI_Flash_Read Ret= 3072
HI_Flash_Read Ret= 3072
HI_Flash_Read Ret= 10485760
HI_Flash_Read Ret= 10485760
******** boot from kernel...********
[HMT]Verify kernel begin.
HI_Flash_Read Ret= 1024
HI_Flash_Read Ret= 1024
The kernel size is [8056832]
16d1853cea8ac28d5d6410e142d5a158271fe26493427aed2739c2700cb99f69
[HMT]Kernel verify OK.
bootargs = coherent_pool=2M console=ttyAMA0,115200 blkdevparts=mmcblk0:1M(fastboot),4M(bootargs),16M(recovery),1M(deviceinfo),4M(baseparam),4M(pqparam),4M(logo),16M(fastplay),8M(misc),24M(factory),12M(kernel),8M(iptv_data),340M(backup),340M(cache),520M(system),-(userdata)HI_Flash_Read Ret= 512
HI_Flash_Read Ret= 512
Stb mac is : [7C:8B:C8:01:0B:FC]
Reserve Memory
Start Addr: 0x3FFFE000
Bound Addr: 0x8E40000
Free Addr: 0x3E507000
Alloc Block: Addr Size
0x3FBFD000 4194304
0x3F8FC000 3145728
0x3F8F9000 8192
0x3F878000 524288
0x3F843000 212992
0x3F742000 1048576
0x3F73E000 12288
0x3EF54000 8294400
0x3EDBE000 1658880
0x3E5D4000 8294400
0x3E507000 835584
Press Ctrl+C to stop autoboot
kernel @ 3e08000 (7723144 bytes)
ramdisk @ 4e00000 (328357 bytes)
page size @ 2048 bytes
initrd rd_start = 4e00000,rd_end = 4e502a5
Booting kernel from Legacy Image at 01ffc7c0 ...
Image Name: Linux-3.10.0_s40
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7723080 Bytes = 7.4 MiB
Load Address: 02000000
Entry Point: 02000000
load:2000000,blob_start:1ffc7c0,blob_end:275a048,image_start:1ffc800,image_len:75d848
Loading Kernel Image ... OK
OK
kernel loaded at 0x02000000, end = 0x0275d848
images.os.start = 0x1FFC7C0, images.os.end = 0x275a048
images.os.load = 0x2000000, load_end = 0x275d848
ret -2
initrd rd_start = 4e00000,rd_end = 4e502a5
HI_Flash_Read Ret= 512
HI_Flash_Read Ret= 512
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
然后就没有然后了……
需要将fastboot替换为原厂的才能刷。
