刚刚刷了机，刷完以后HiTool完成，机顶盒界面也是Linux我是小盒子 也是大世界
终端跑码但是按回车不能登陆，关闭电源重启也无效
跑码如下
Bootrom start
Boot Media: eMMC
Decrypt auxiliary code ...OK
Enter boot auxiliary code
Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Jul 28 2018 - 18:30:32
Reg Version: v1.6.0\
Reg Time: 2017/12/12 16:53:03
Reg Name: hi3798mv2dma_hi3798mv200_DDR3-1866_1GB_16bitx2_2layers.reg
Boot auxiliary code success
Bootrom success
System startup
Relocate Boot
Jump to C code
Fastboot 3.3.0_ecoo_82100468-dirty (teasiu@ecoo) (Oct 04 2022 - 16:26:15)
Fastboot: Version 3.3.0
Build Date: Oct 4 2022, 16:27:08
CPU: Hi3798Mv200
Boot Media: eMMC
DDR Size: 1GB
Found flash memory controller hifmc100.
no found nand device.
MMC/SD controller initialization.
HIMCI_ERROR hi_mci_cmd_done:508: Is Card error: Device not switch to the expected mode
HIMCI_ERROR hi_mci_cmd_done:508: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:508: Is Card error: status bit
unfound correct edge! check your config is correct!!
MMC/SD Card:
MID: 0x11
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 3776M Bytes (High Capacity)
Name: "004G60"
Chip Type: MMC
Version: 5.0
Speed: 52000000Hz
Mode: DDR50
Voltage: 1.8V
Bus Width: 1bit
Boot Addr: 0 Bytes
Net: eth0 phymdio(31) invalid, use default:0
up, down, gmac0
Boot Env on eMMC
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000
SDK Version: HiSTB_com_NAS_ubuntu_20220427
mmc read failed
Reserve Memory
Start Addr: 0x3FFFE000
Bound Addr: 0xF900000
Free Addr: 0x3F4F9000
Alloc Block: Addr Size
0x3FFFB000 0x2000
0x3FF7A000 0x80000
0x3FF49000 0x30000
0x3FE88000 0xC0000
0x3F69D000 0x7EA000
0x3F699000 0x3000
0x3F503000 0x195000
0x3F4F9000 0x9000
Press Ctrl+C to stop autoboot
MMC read: dev # 0, block # 28672, count 81920 ... mmc read failed
-1 blocks read: ERROR
779571768 Bytes/s
Load fip from 0x1FFFFC0 ...
Firmware Image Package ToC:
- EL3 Runtime Firmware BL3-1: offset=0x88, size=0x7020
- Non-Trusted Firmware BL3-3: offset=0x70A8, size=0x14BA2EE
---------------------------
Create Entry Point info ...
Get - EL3 Runtime Firmware BL3-1
Get - Non-Trusted Firmware BL3-3
bl33_ep->spsr = 0x3C5
ATAGS [0x00000100 - 0x0000042C], 812Bytes
Move bl31 img from 0x02000048 to 0x4400000, 28704 Bytes
Start Warm Reseting
NOTICE: BL31: v1.2(debug):7c42f9e5
NOTICE: BL31: Built : 16:49:52, Oct 4 2022
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to secure world
INFO: Entry point address = 0x20070a8
INFO: SPSR = 0x3c5
DTB: 034bdb58 00077800 000037fe
Kernel: 020081c8 00080000 014b5990
booting the arm64 kernel.
求指教
