emmc failed

takina

Bootrom start
Boot Media: eMMC
Decrypt auxiliary code ...OK
Enter boot auxiliary code

Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Jul 28 2018 - 18:30:32

Reg Version: v1.6.0\
Reg Time: 2017/12/12 16:53:03
Reg Name: hi3798mv2dma_hi3798mv200_DDR3-1866_1GB_16bitx2_2layers.reg

Boot auxiliary code success
Bootrom success

System startup

Relocate Boot

Jump to C code

Fastboot 3.3.0_ecoo_82100468-dirty (teasiu@ecoo) (Oct 04 2022 - 16:26:15)

Fastboot: Version 3.3.0
Build Date: Oct 4 2022, 16:27:08
CPU: Hi3798Mv200
Boot Media: eMMC
DDR Size: 1GB

Found flash memory controller hifmc100.
no found nand device.

MMC/SD controller initialization.
HIMCI_ERROR hi_mci_cmd_done:508: Is Card error: Device not switch to the expected mode
HIMCI_ERROR hi_mci_cmd_done:508: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:508: Is Card error: status bit
unfound correct edge! check your config is correct!!
MMC/SD Card:
MID: 0x11
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "008G30"
Chip Type: MMC
Version: 5.1
Speed: 52000000Hz
Mode: DDR50
Voltage: 1.8V
Bus Width: 1bit
Boot Addr: 0 Bytes
Net: eth0 phymdio(31) invalid, use default:0
up, down, gmac0

Boot Env on eMMC
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000

SDK Version: HiSTB_com_NAS_ubuntu_20220427

mmc read failed
Reserve Memory
Start Addr: 0x3FFFE000
Bound Addr: 0xF900000
Free Addr: 0x3F4F9000
Alloc Block: Addr Size
0x3FFFB000 0x2000
0x3FF7A000 0x80000
0x3FF49000 0x30000
0x3FE88000 0xC0000
0x3F69D000 0x7EA000
0x3F699000 0x3000
0x3F503000 0x195000
0x3F4F9000 0x9000

Press Ctrl+C to stop autoboot

MMC read: dev # 0, block # 28672, count 81920 ... mmc read failed
-1 blocks read: ERROR

779417244 Bytes/s
Load fip from 0x1FFFFC0 ...

Firmware Image Package ToC:

EL3 Runtime Firmware BL3-1: offset=0x88, size=0x7020
Non-Trusted Firmware BL3-3: offset=0x70A8, size=0x14BA2EE
---------------------------
Create Entry Point info ...
Get - EL3 Runtime Firmware BL3-1
Get - Non-Trusted Firmware BL3-3
bl33_ep->spsr = 0x3C5
ATAGS [0x00000100 - 0x0000042C], 812Bytes
Move bl31 img from 0x02000048 to 0x4400000, 28704 Bytes
Start Warm Reseting
NOTICE: BL31: v1.2(debug):7c42f9e5
NOTICE: BL31: Built : 16:49:52, Oct 4 2022
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to secure world
INFO: Entry point address = 0x20070a8
INFO: SPSR = 0x3c5

reloc: bad dtb magic.

-- System halted

takina

Bootrom start
Boot Media: eMMC
Decrypt auxiliary code ...OK
Enter boot auxiliary code

Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Jul 28 2018 - 18:30:32

Reg Version: v1.6.0\
Reg Time: 2017/12/12 16:53:03
Reg Name: hi3798mv2dma_hi3798mv200_DDR3-1866_1GB_16bitx2_2layers.reg

Boot auxiliary code success
Bootrom success

System startup

Relocate Boot

Jump to C code

Fastboot 3.3.0_ecoo_82100468-dirty (teasiu@ecoo) (Oct 04 2022 - 16:26:15)

Fastboot: Version 3.3.0
Build Date: Oct 4 2022, 16:27:08
CPU: Hi3798Mv200
Boot Media: eMMC
DDR Size: 1GB

Found flash memory controller hifmc100.
no found nand device.

*** Warning - bad CRC or eMMC, using default environment

Net: eth0 phymdio(31) invalid, use default:0
up, down, gmac0

Boot Env on eMMC
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000

SDK Version: HiSTB_com_NAS_ubuntu_20220427

Reserve Memory
Start Addr: 0xFFFE000
Bound Addr: 0xF900000
Free Addr: 0xFFFE000
Alloc Block: Addr Size

Press Ctrl+C to stop autoboot

takina

fastboot# printenv
bootargs=mem=256M console=ttyAMA0,115200 console=ttyMTD,blackbox
bootcmd=
bootdelay=1
baudrate=115200
ethaddr=00:00:00:00:00:00
ipaddr=192.168.1.10
serverip=192.168.1.1
netmask=255.255.255.0
bootfile="uImage"
stdin=serial
stdout=serial
stderr=serial
ethact=up
bootargs_512M=mem=512M mmz=ddr,0,0,256M
bootargs_1G=mem=1G mmz=ddr,0,0,380M
bootargs_2G=mem=2G mmz=ddr,0,0,600M
ver=Fastboot 3.3.0_ecoo_82100468-dirty (teasiu@ecoo) (Oct 04 2022 - 16:26:15)

Environment size: 450/65532 bytes

takina

Bootrom start
Boot Media: eMMC
Decrypt auxiliary code ...OK
Enter boot auxiliary code

Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Nov 29 2017 - 19:57:41

Reg Version: v1.5.7\
Reg Time: 2018/02/24 10:06:55
Reg Name: hi3798mv2dma_hi3798mv200_DDR3-1866_1GB_16bitx2_2layers.reg

Boot auxiliary code success
Bootrom success

System startup

Relocate Boot

Jump to C code

Compressed-boot v1.0.0
Uncompress......................Ok

System startup

Relocate Boot

Jump to C code

Fastboot 3.3.0 (root@HW-TV-S12) (May 03 2018 - 14:35:21)

MMC/SD controller initialization.

SDK Version: HiSTBAndroidV600R003C01SPC030_v2018042310

Begin to show boot logo through Logo_Main.
Logo_Main End.
Net: eth0 phymdio(31) invalid, use default:0
up, gmac0

SET BIT(40,0)==>x3

======== HMT_IR_getKey start Second ========
get key value 0x0 g_Left_KeyDown=0 g_Right_KeyDown=0
check remote recovery button begin
The mac is not a valid mac, use default mac.
HI_Android_Authenticate,122: secure chip flag = 0
enter write OTP mode!
env bootcmd:mmc read 0 0x1FFBFC0 0x3D000 0x4400; bootm 0x1FFBFC0

MMC read: dev # 0, block # 249856, count 17408 ... 17408 blocks read: OK

88021068 Bytes/s
Check Hisilicon_ADVCA ...
Not hisilicon ADVCA image ...
Check Hisilicon_ADVCA ...
Not hisilicon ADVCA image ...
Wrong Image Format for bootm command
ERROR: can't get kernel image!

MMC read: dev # 0, block # 249856, count 17408 ... 17408 blocks read: OK

88021068 Bytes/s
Check Hisilicon_ADVCA ...
Not hisilicon ADVCA image ...
Check Hisilicon_ADVCA ...
Not hisilicon ADVCA image ...
Wrong Image Format for bootm command
ERROR: can't get kernel image!

uhkai

和你一模一样的报错，请问你解决了吗？

开源、免费、互助、进步

e 酷网 www.ecoo.top 2023